FLDIGI SIGNALINK USB SETUP MANUAL
FLDIGI SIGNALINK USB SETUP PRO
FLDIGI SIGNALINK USB SETUP SOFTWARE
FLDIGI SIGNALINK USB SETUP LICENSE
FLDIGI SIGNALINK USB SETUP DOWNLOAD

If the message is not legible, verify the SQL button in the lower right portion of the screen is checked yellow, and adjust the squelch bar next to the SQL button. If your equipment and configurations are set correctly, you will automatically receive messages in the upper text box. Once your message is sent, click the RX button to stop transmission

Type your message in the blue box then click the purple TX button below the text. Then, verify you have the correct frequency entered in your radio before you start transmitting and receiving messages. You are almost ready to type and send your digital message:Ĭonnect the cables from your Signalink to the radio and computer. or the Scheduled Nets page for the operation mode and frequency)Ħ) Enter the call sign you want to call.

Save and close window.ĥ) Next, select the mode and you want to use in the fldigi program Click “save” and close.Ģ) Plug Signalink into the USB port and press red PWR button “on”.ģ) Click “configure” tab and then select “sound card” from the drop down menu.Ĥ) Select the USB options in the drop-down on both Capture and Playback. Once you have it downloaded, follow the steps below:ġ) Click on configure, then the operator tab and enter your FCC call sign.

FLDIGI SIGNALINK USB SETUP DOWNLOAD

To get started, you will need to download fldigi.Ĭonfiguring fldigi is quick and simple.

FLDIGI SIGNALINK USB SETUP MANUAL

Once you have your gear, review the Signalink manual that came with your equipment to get your jumpers or Plug & Play installed. The purpose of the Signalink device is to act as an external sound card for your computer, making it compatible with other users’ computers. TigerTronics has a customer service department if needed. Verify you are ordering the correct Signal Link and Jumper for your specific radio. NOTE: The Signal Link and Plug & Play linked above is for the BaoFeng UV-5R. Here is a picture of an example of a basic digital comms setup:ġ) Computer (laptop, netbook, etc.) to run the free downloaded copy of fldigiģ) Signal Link USB for UV-5R (comes with cables and jumpers)Ĥ) Plug & Play Jumper (recommended for easier set up instead of using jumpers) However, it does not require an internet connection for transmitting and receiving-it uses radio waves.

FLDIGI SIGNALINK USB SETUP SOFTWARE

It just sounds like a ‘humming or buzzing’ noise while transmitting to anyone monitoring the frequency without the digital equipment.ĭigital communications does require a computer since it uses software such as fldigi. Another benefit is, digital communication can only be ‘decoded’ by others set up for digital communications.

FLDIGI SIGNALINK USB SETUP LICENSE

NOTE: A Ham License is required to TRANSMIT on digital modesĭigital communications requires less power, transmits farther and is reliable even in poor conditions. Once you get your digital communications running, help others in your network and consider starting a local digital net! This post will show you what basic equipment is needed to get started. These dongles are also prone to overloading (particularly from AM and FM stations in urban areas) due to rather limited (if it exists at all) filtering (as I've been reading in the various forums and blogs).Digital communications is not as scary as it sounds.

There'ss a wide assortment of modes and software that are mentioned here, including using FLDigi on Olivia and MFSK16 (not PSK31, yes, but the concept is the same here) There are a couple of errors in the article, but you get the idea that it can be done. Since you didn't mention which dongle you were looking at, this article by Nils DK8OK is on using the Funcube Dongle on various modes (it's a PDF). In Fldigi Go to Configure -> Config Dialog Go to Soundcard -> Devices Check the PortAudio box and select the name of the USB Audio Codec device for Capture and Playback. It certainly is possible - most likely you would need software like Virtual Audio Cable to get the data from the dongle to the PC.

FLDIGI SIGNALINK USB SETUP PRO

Such dongles include the Funcube Dongle Pro v2.0, SDRStick and the RTL-SDR with an appropriate up-converter (or one built into the board itself - there are a few like this, some of which are linked in the article below.) (USB audio codec) On your computer open the sound mixer and select the USB audio codec. Set up Fldigi audio.make sure it is looking at the Signalink for both TX and RX audio. Unfortunately the Signalink is not a USB Dongle - it is an interface that feeds a soundcard.A SDR dongle is a whole 'nother animal. Open Fldigi,set mode to bpsk-31,set cursor on the waterfall to 1500Hz, open mixer applet on computer by right-click on speaker icon.

Fldigi signalink usb setup